Go to content

5 steps for a clean cooling system – MEYLE shows how it’s done!

Hamburg, 12 December 2018: Thorough and regular flushing is one of the decisive steps in the maintenance of cooling systems. Contamination, e. g. due to the incorrect use of sealing compound in the cooling system, reduces the cooling capacity in the long run and can lead to premature failure of the water pump mechanical seal. But even beyond this, proper flushing of the cooling circuit is the basis forlonger engine service life. This should take place at the latest when the water pump is replaced in order to remove particles that can be caused by corrosion or limestone. The Hamburg-based manufacturer MEYLE now supports workshops with a special tool. With this tool, which MEYLE offers in a joint cooperation with its partner HAZET, the cooling system can be cleaned with the aid of water and compressed air – completely without aggressive chemicals and cleaners. MEYLE shows how the engine cooling circuit can be cleaned in five simple steps.

5 steps for a clean cooling system – MEYLE shows how it’s done!

Step 1: Preparation

The engine must be completely cooled down before starting work. The old coolant is then drained and the coolant expansion tank cleaned or replaced if heavily soiled. For environmental reasons, it is important to dispose of the waste liquid properly.


Step 2: Flushing the cooler

Remove the upper and lower radiator hoses on the radiator. The lower radiator hose is thoroughly rinsed from bottom to top for about two minutes with the radiator cap closed using the MEYLE tool. Short pulses of pulsating air into the system increase the effectiveness. The upper radiator hose can then be flushed from top to bottom until the outflowing water is clear and deposits have been removed. 


Step 3: Flush engine block

Next, remove the radiator hoses. Using the MEYLE cooling circuit flushing tool, the upper radiator hose is thoroughly flushed until the outflowing water remains clear and any deposits have been removed. Also in this step short pulsating air blows increase the effectiveness of the rinsing process. 


MEYLE workshop advice: If the thermostat blocks proper rinsing, it must be removed for rinsing. In this context, MEYLE recommends a general replacement of the thermostat.   


Step 4: Flush the heat exchanger

If possible, the circuit to the heat exchanger should also be flushed until the outflowing water is clear. As a general rule, flushing the radiator, engine block and heat exchanger removes deposits of corrosion, limestone and silicone seal residues from the cooling system. These can accumulate over many years and permanently impair the functionality of the system.


Step 5: Refill the system

In the final step, all hoses, the drain valve and the thermostat are reattached. It must be checked whether all necessary connections have been made again. The cooling system can then be refilled with the coolant specified by the manufacturer. The mixing ratio should, for example, be checked with a refractometer. Finally, the system should be properly vented. A final check ensures that there are no leaks.


All steps can also be followed on the YouTube channel MEYLE TV in a short video tutorial. This shows how to clean the engine cooling system cleanly and safely with the MEYLE cooling circuit flushing unit. This ensures that all components of the flushing circuit, such as the water pump, function continuously and reliably. 

Some Background: MEYLE water pumps

Thanks to sophisticated details such as the wear-resistant SiC/SiC mechanical seal, which is used in all MEYLE-HD and a majority of all MEYLE-ORIGINAL water pumps, and the highly robust water pump bearing, MEYLE water pumps are exceptionally reliable. MEYLE therefore also provides a 100,000-mile guarantee for all MEYLE water pumps and a 4-year guarantee for MEYLE-HD water pumps. The guarantee* requires the cooling system to be flushed before installation.



Disassembly and installation must always be carried out by trained personnel. Please follow the instructions of the vehicle manufacturer exactly. MEYLE AG does not assume any responsibilities, disclaims or any liabilities if the activities shown in the video are imitated.

*See more information: www.meyle.com/guarantee 


Download our press releases and press pictures from www.meyle.com or order in electronic file format.

To download this press photo please click here: download

Download (DOCX 165 KB)



MEYLEニュースレター:最新の製品情報、カレンダーアップデート等をご覧頂けます。 - 今すぐお申込みください!


MEYLE自動車用スペアパーツについてお知りになりたい情報は、 MEYLE パーツアプリのボタンを押すだけでご覧頂けます。